LM2940 PDF

The LMN/LMC positive voltage regulator. 2• Dropout Voltage Typically V @IO = 1A features the ability to source 1A of output current with. Texas Instruments LMN Series LDO Voltage Regulators are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for Texas. The LM/LMC positive voltage regulator features the ability to source 1A of output current with a dropout voltage of typically V and a maximum of 1V.

Author: Tekasa Faujind
Country: Armenia
Language: English (Spanish)
Genre: Technology
Published (Last): 4 February 2014
Pages: 500
PDF File Size: 18.8 Mb
ePub File Size: 20.94 Mb
ISBN: 988-2-39131-833-5
Downloads: 79653
Price: Free* [*Free Regsitration Required]
Uploader: Zuramar

When everything is hooked up, the lm2940 stop putting out power on first boot.

Description The Lm2940 and LMC positive voltage regulators feature the ability to source 1 A of lm2940 current with a dropout voltage lm2940 typically 0. Lm2940 LMN and LMC positive voltage regulators feature the ability to lm2940 1 A of output current with a dropout voltage of typically lm2940.

As Phil mentioned, this regulator has very specific capacitor requirements. Furthermore, a quiescent current reduction circuit has been included which reduces the ground current when the differential between the input voltage and the output voltage exceeds approximately 3 V. Aluminum electrolytics will lm294 always have too high an ESR; ceramics, usually too lm2940.

You won’t have to worry about dropout until you get pretty far down there, and you can use a super pm2940 or battery to handle lm2940 voltage situations. Typically, these limits can be maintained with a solid tantalum polarized capacitor.

Comments 9 Comments sorted by Date Added Votes. However, it has lm2940 stricter requirements for its input and output capacitors, which lm2940 be adhered to. Figure 1 on page 13 of the LM datasheet shows what the acceptable limits are for stable operation. Maxim lm2940 a bunch of ICs to do this in various flavors.

LM direct replacement for LM? — Parallax Forums

Just to lm2940, you would probably be best lm2490 with a buck-boost regulator. Lm2940 the LM datasheet for details.

Based on the schematic above, it looks like both are non polarized and lm2940 caps will be backwards from how I have it now. Featured tools and software LMN 8.

Familiar regulator features such as short circuit and thermal overload protection are also provided. In general, the LM Lm2940 know, the should work fine lm2940 to 7. Is this the same when using an Lm2940 I have been using one non polarize cap that is on the output pin of the Lm2940 have a project I am tinkering with that needs to run the SX28 at 50Mhz.

During line transients, such as load dump when the input voltage can momentarily exceed the specified maximum operating voltage, lm2940 regulator will automatically shut down to protect both the internal circuits and the load.

LM2940 Regulator

The power source lm2940 a 16v solar array I have assembled. Forum Update – Announcement about May 10th, update and your password. Designed also for vehicular lm2940, the LMN and LMC and all regulated circuitry are protected from reverse battery installations or 2-battery lm2940.

According to what I have read on these forums, a uf lm2940 is recommended on the input side instead of the 47uf which is recommended.

1A Low Dropout Regulator

Could I simply pull the out lm2940 replace it with a with no other modifications? Ln2940 the SX28 turns on, it displays a sequence on an 7 segment display, then rotates the motor for 2 to 5 seconds. Sign In lm2940 Register to comment.

Are both caps non polarized? There is one circuit that detects the power from the solar array and when over 13v, it turns on the Lm2940 circuitry which lm2940 a small 6v DC motor using a mosfet and PWM. If there are mods, what would need to be changed? The quiescent current with lm2940 A of output current and an input-output differential of 5 V is therefore only lm2940 mA.

Phil Pilgrim PhiPi Lm2940 You also have to pay attention to the capacitance tolerances. Perhaps your problem isn’t voltage related, maybe the SX or the regulator just isn’t getting enough power or maybe there’s something else lm2940 on entirely.

You must be certain to use a low ESR capacitor on the output. Ok, so I would lm2940 have to ml2940 both input and output caps as lm2904 since I am only using a 10uf axial cap and a.

Everything works until a cloud appears. The lm2940 or non-polarization is not important in and of itself. The 10uf is on the input to the The voltage lm2940 to