HCPLE Broadcom / Avago High Speed Optocouplers 10MBd 2Ch 5mA datasheet, inventory, & pricing. Logic Output Optoisolator 10MBd Open Collector, Schottky Clamped Vrms 2 Channel 10kV/µs CMTI 8-SO Tall. Logic Output Optoisolator 10Mbps Open Collector, Schottky Clamped Vrms 2 Channel 5kV/µs CMTI 8-SO Tall.
|Published (Last):||21 September 2007|
|PDF File Size:||16.97 Mb|
|ePub File Size:||12.89 Mb|
|Price:||Free* [*Free Regsitration Required]|
A lot hcpl-0631 other people are on this forum and it may help everyone if you attached your Multisim file. Save this item to a new parts list. Your circuit is wrong. The resistor R1 should be a pull up resistor connected between hcpl-0631 output and your power rail, not a pull down resistor like the way you’ve connected it.
You should also have a ground attached to the cathode of the optoisolator or neutral wire of the function generator. Message 8 of 9. Will it be possible for you to tell me where have gone wrong in my circuit hcpl-0631 Multisim constructs mesh current and node voltage hcpl-0631 for simulation and can’t do it accurately if you don’t specify the ground hcpl-0631 your circuit.
The hcpl-0631 of the optocoupler has an open collector NPN driver. The Manufacturers disclaim all warranties including implied warranties of merchantability or fitness for a particular purpose and are not liable for any damages hcpl-0631 from your use of or your inability to use hcpl-0631 Information downloaded from this hcpl-0631.
Thanks for helping us to improve our site
hcpl-0631 I am trying to use the HCPL optocoupler for my simulation. Hcpl-0631 bet that you hcpl-0631 figure it out if you debugged the circuit by tracing the signal from the circuit’s input to its output. It doesn’t actual have a open collector output. You agree that the Hcpl-0631 as provided here through an intermediary may not be error-free, accurate or up-to-date and that it is not advice. Save to parts list Save to parts hcpl-0631.
I think the current limiting resistor connected to the diode input is too large.
HCPL – Avago Technologies US, Inc. – Isolators – IN STOCK –
Auto-suggest helps you quickly narrow down your search hcpl-0631 by suggesting possible matches as you type. It also has a built hcpl-0631 VCC of 5V, so the power hcpl-0613 that you are attaching isn’t really being used. The Manufacturers reserve the right to change this Information at any time without notice. I have added a ground on hcpl-0631 right have side of the circuit and it worked.
Message 9 of 9. Hcpl-0631 6 of 9. Image representative of range hcpl-0631. Please advice me what other options can I use or solutions to my hcpl-0631. RoHS Certificate of Compliance. Please enter a message.
Hcpl, Hcpl Suppliers and Manufacturers at
Please select an existing parts list. Try adding a ground to the GND terminal hcpl-0631 the optoisolator. Ahh, I see hcpl-0631 problem. Sorry I am hcpl-0631 the printscreen of my circuit here is an updated one.
Message 3 of 9. Take a look at the datasheet. Save to an existing parts list Save to a new parts list.
I have attached the circuit diagram in the attachment, hcpl-0631 let me know hcpl-0631 is wrong with my circuit causing the components to fail. Accepted by topic author hcpll-0631. Try using a resistor between hcpl-0631 ohms on the input. Message 7 of 9. I wouldn’t be able to tell you as the circuit looks a bit complex. Let me know thanx. Optocoupler, 10MBd Logic Gate, Avago Technologies 10 MBd digital optocouplers are suited for isolated communication logic hcpl-0631 and control in industrial power systems, factory automation, power supplies, and medical equipment applications.
You have hcpl-0631 to save the following item to a parts list:. Hcpl-0631 Active Software Boards: Message 5 of 9.
Your problem is grounding. Message Edited by justinycc on bcpl-0631 However, this optocoupler will hcpl-0631 function properly hcpl-0631 will not give me a good result. I have been going to the optocouple list in multisim and hcpl-0631 find any other model that has an amplifier inside the optocoupler apart from this HCLP Thank you for your hcpl-0613. Message 4 of 9. I have also tried other values as well but it still wouldn’t work. The product does not contain any of the restricted substances in hcpl-0631 and applications banned by the Directive, and for hcpl-0631, the product is capable of hcpl-0631 worked on at the higher temperatures required by lead—free soldering.
HCPL is not functioning properly hcpl-0631 help!! Actually, never mind hcpl-0631 that, the model for the HCPL isn’t very good.
Message 2 of 9. Sending feedback, please wait